VW 8V 276 N/A application hydraulic tappets performance camshaft + High Compression Head Gasket - 0.5mm + 118mm head stud set
VW 8V 276 N/A application hydraulic tappets performance camshaft
Application: EA 827 engines Capacities 1781-1847-1984cc from 1986
8V Engines with hydraulic tappets
VW Golf, Corrado, Audi 80, 100, 5000, Quattro, Jetta, Passat, Scirocco, Sharon, Vento, Gol, Pointer, Saveiro.
Duration intake: 276 degrees
Duration exhaust: 276 degrees
Intake valve lift: 11.50mm
Exhaust valve lift: 11.50mm
lobe centers: 110 degrees
valve timing
Intake open: 27 degrees
Intake closes: 69 degrees
Exhaust open: 67 degrees
Exhaust close: 29 degrees
Valve clearance: hydraulic lifters*
Base circle: 34mm
Made of 1045 quenched steel
Billet machined
52-58 HRC
IMPORTANT: this is a performance camshaft, not a OEM replacement, installation may require ECU work, cylinder head work, special lifters and springs, no instructions included, no other parts included.
Attention: this camshaft can be used with solid lifters as long as valve lash caps (EMPI 4006, or similar) are assembled and adjusted individually. We strongly recommend that this should be done by a proper professional in order to achieve the correct valve lash values.
VW 8v/16v ABA ABF MLS High Compression Head Gasket - 0.5mm
- Special cylinder head gasket for turbo conversion
- With this special Turbo multilayer metal cylinder head gasket
- The compression raise is already integrated in the seal.
- (Ground and coated)
- Will accept pistons up to 84.00mm overbored sized, can be used with smaller bores with no problem too.
- Compression ratio NEW will depend on the engine used
- Manufacturer: SPA TURBO
- Engine Code: All 2 liters Blocks of VW 8V and 16V (some small modifications may be necessary in some cases)
- 9A, 6A, ACE, 2E, ADY, ACX ABF, AGG, AKR, ABA, ABBOT, ADW, AAD, AAE, CAST OFF, 3A, SD.
- Similar to OE numbers/Comparable numbers of manufacturers
- Available in 0.9mm; 1.5mm; 2.0mm, 2.5mm and 3.4mm thickness
- We're the VW Turbo experts!
VW MKI MKII GTI PB 1.8L 2.0L 8v SOHC 118mm head stud set
- VW cylinder head stud set, available in either 118mm (this item) or 136mm length for taller blocks.
- They will fit earlier and old style VW 8V cylinder heads.
- The set contains 10 Studs, 10 washers and 12 point nuts, (you will need a 1/2 or 13mm 12 point socket).
- The studs are for M11 threads, please confirm with your OEM bolts before purchase.
- These will replace 93mm OEM bolts.
- Maximum Torque - 72 ft/lb
Product Disclaimer:
Emissions Equipment Tampering Warning: In many states, tampering with your vehicle’s emissions equipment is unlawful. Our products are designed and sold for sanctioned off-road/competition non-emissions controlled vehicles only and may never be used on a public road or highway.
Using our products for street/road use on public roads or highways is prohibited by law unless a specific regulatory exemption exists (more information can be found on the SEMA Action Network website www.semasan.com/emissions for state-by-state details in the USA).
CARB-Restricted Areas: CARB-Restricted products, will not be shipped to state of California under any circumstatences.
Official Air Resource Board Link: ARB State Adoption Link
Customer Responsibility: It is the responsibility of the installer and/or user of this product to ensure compliance with all applicable local and federal laws and regulations. Please check with your local vehicle authority before purchasing, using, or installing any of our products.
By proceeding with the purchase and use of our products, customers affirm their commitment to adhere to the terms outlined in this comprehensive product disclaimer. We reserve the right to update this disclaimer as necessary.
